Detection and locating, measuring equipment
Water leak detector, cable and pipe locators

Cable and pipe locator "Success AG-309.15G"

High tech device for detection of cables and any metal pipelines with integrated GPS/GLONASS module.

Features:

  • Monoblock receiver AP-019.3 with built-in GPS/GLONASS module
  • 20W AG-105 transmitter
  • high precision location of underground utilities up to 10m
  • direct digital measurement of cable current up to 10 amperes
  • Location of non-conductive and non-metallic utilities with optional pushing rod and pipe sonde

Overview

Brief description:

  • three modes of operation : "ROUTE”, "GRAPHIC”, “FRIEND-OR-FOE”
  • three inbuilt sensors make omnidirectional antenna showing a direction of a cable or a metal pipeline on LCD display
  • inbuilt sensor for digital measurement of the depth and current
  • measured depth is 10 m
  • passive frequency: Power, Radio, BB
  • active frequency: 512/1024/8192/32768 Hz
  • sensitivity : 100μA
  • large LCD display with high resolution and adjustable backlight brightness
  • transmitter – 20W
  • cast body, the case is sealed along the entire length to the connectors
  • GPS/GLONASS module for accurate positioning of the located utility
  • Mini-USB cable and desktop software for uploading and processing the data from the receiver.

Application:

  • Detection of cables and any metal pipelines underground up to 10 m
  • Direct digital measurement of the depth up to 10 m
  • Indication of the deviation from the utility axis in the mode “ROUTE”
  • Direct digital measurement of the current
  • Survey the ground before the excavation works
  • Distance of tracing from the place of transmitter connection is up to 3 km

Cable locator Success AG 309.15G - extended set

Success CBI-309G (N) Route mode, passive cable location

Success AG-309.15G (N) Cable location with the transmitter


AP-019.3 GPS/GLONASS operation

Transmitter АG-105

Specifications

Receiver AP-019.3 Specifications

Parameter Value
Quasi-resonant frequencies of the filter 50(60) / 100(120) / 512 / 1024 / 8192 / 32768 Hz
Quasiresonant filter quality factor (Q) Not less than 100
Frequency range "Broad band" 0,04 to 8 kHz
Frequency range "Radio" 8 to 40 kHz
The maximum gain of the electric path >100 dB
Number of built-in sensors 4
Connected external sensors CI-105, HP-117, DODK-117, DKI-117 (made by «TECHNO-AC»)
Sensitivity control Auto - for 2D display «Route». Semi-automatic or manual (optional) - for the «Graphics». Automatic or manual (optional) - for the «2F» mode.
Determination the burial depth of the route Automatically in the mode Route 0 to 9,99 m
The accuracy of determining of the depth ±5%
Measurement of the current of the signal received Automatically in the mode Route 0.001 to 9,99 A
Accuracy of the measurement of the current of the signal received ±5%
Support of energy saving (intermittent) modes of the route locating generators At combined work with the route locating generators made by "TECHNO-AC" ("Pulse" mode)
Visual indication LCD display, 320x240 pix., LED lighting
Induced parameters

- parameters of setting and control;

- 2D visualization of the route location relative to the device;

- graphics of the signal level from sensors;

- route burial depth;

- signal current.

Audio indication Built-in transmitter - synthesized sound HM- sound indication of buttons pressing
Power supply source 4 to 7 V (4 elements of C type)
Time of continuous work from the one complete of the alkaline batteries Not less than 20 hours
Temperature range for storage / operation -30 to 60°С / -20 to 60°С
House protection degree IP54
Dimensions 330x140x700 mm
Weight 2,4 kg

 

Transmitter AG-105 Technical specifications

The frequencies of the continuous «Co» or pulse «Pu» signal, Hz ± 0,1% - «kHz»
Load «clips» or «clamp» 512 - «0.5» / 1024 - «1.0» / 8192 - «8.2» / 32768 - «33»
«Antenna» modes 8192 - «8.2» / 32768 - «33»
Operating modes
«Antenna» modes Internal transmitting inductor «In».
External induction transmitting antenna «An».
«Modulation» modes (special form signal) Pulse «Pu» (short-term transmissions of the sine signals). Transmission duration 0,12sec. Transmissions repetition frequency 1Hz.
Dual-frequency «2F» (simultaneous frequency generation 1024Hz, 8192Hz). Amplitudes ratio 4/1 (respectively).
Output parameters under power supply voltage 12…15V
Output current, А
Restricted by the program under manual increment, 5 – at frequency 512Hz «0.5» / 1024Hz «1.0» / 8192Hz «8.2» / «2F»
3 - at frequency 32768Hz «33»
Set by the program for automatic adjustment with the external load of «clips» or «clamp», ≥ 0,2 – at frequency 512Hz «0.5» / 1024Hz «1.0» / «2F»
0,1 – at frequency 8192Hz «8.2» / 32768Hz «33»
Maximum output voltage, V
Depending on «modulation», ≥ 32 – in the dual-frequency modulation mode «2F»
40 – in other modes
Maximum output power, W
Restricted by the program, ≥ 20 - In the continuous «Co» and pulse «Pu» modes at frequencies 512Hz «0.5» / 1024Hz «1.0» / 8192Hz «8.2» at load resistance up to 80Ω In dual-frequency mode «2F» at load resistance up to 50Ω.
6 - At frequency 32768Hz «33» at load resistance up to 260Ω.
Power supply sources
Operating range of the supply voltages Minimally acceptable voltage for oscillation start-up - 7V.
Maximum allowed voltage for operation – 15V.
Automatic shutdown voltage in the “oscillation” mode < 4,2V.
Battery set 8 «alkaline» cells 1,5V «type С» Recommended – «Duracell ® ULTRA».
External power supply sources (optional) Battery «12V» (e.g. automotive) Output voltage 11…14V, maximum current not less than 4А.
Mains power supply adapter АG114М.02.020 (extra accessory based on GS60A15-P1J «MEAN WELL») Output voltage 15V, power 60W.
Operating time («life cycle») While in operation of the battery set «type Сх8» is defined by the quality (capacity and «load capability») of the applied alkaline cells and can be equal to from 4 to 6 hours in the «Co» и «2F» modes or from 20 to 30 hours in the «Pu» mode at initial output voltage 7W in «continuous» modes «Co» / «2F» or at initial output voltage 15W in pulse modulation mode «Pu».
Under the external power supply is fully conditioned by this external energy source characteristics therefore under mains supply operating time is unlimited.
Operational characteristics
An automatic control over the output voltage during oscillation process Proportional control over the output power depending on the “energy potential” of the power supply source.
Automatic shutdowns of the device At power supply voltage in the “stop” mode < 6,5V.
At power supply voltage in the “oscillation” mode < 4,2V.
At power supply voltage > 15,5V.
In case of exceeding of the admissible absorbed current value (the exact figure depends on the actual mode).
In case of short circuit of the output during the adjustment process (actuation of the hardware safety system of the terminal amplifier).
In case of non-compliance of the oscillation mode settings depending on whether the external antenna is installed in the output or not (the switch to the “stop” mode).
In case of “long” (≈ 100sec) downtime in the “stop” mode (if the buttons are not pushed).
Adjustment with load Automatic, up to the reaching of the specific consumption rate or attainment of the load current: - ≥ 0,2А at frequencies 512Hz «0.5» / 1024Hz «1.0» / «2F»; - ≥ 0,1А at frequencies 8192Hz «8.2» и 32768Hz «33».
Manual after the automatic adjustment.
Connection options to the utility under examination «Contact» connection with “earth return”.
«Non-contact» connection with application of the internal transmitting antenna «In».
«Non-contact» connection with the use of external induction transmitting antenna «An» (the emission intensity is higher and easier access to the utility in comparison with the internal transmitting antenna «In»).
«Non-contact» connection using the transmitting induction “clamp” (selection of the cable from the bunch is possible).
Structural parameters
Power output amplifier The technology — updated CLASS D Efficiency to 85%.
LED indicators Separate light-emitting diodes indicating parameters and modes.
Digital indicator displaying the modes and parameters values and also showing output parameters of the «MULTIMETER» measurements, e.g.: output voltage (V), load current (А), load power (W) and load resistance (Ω /kΩ).
Overall dimensions of the electronic unit (case), not more than, mm. 216х180х105mm
The weight of the electronic unit, not more than, kg 2
 
The admissible environment temperatures range when in operation - 30°С to +60°С With “battery” power supply it is not recommended to use the device under sub-zero environmental temperatures.
Ingress protection rating IP65 (when the enclosure-case is shut).

Standard set

  • Receiver АP-019.3
  • Transmitter АG-105
  • CD with desktop software
  • Mini-USB cable
  • Power connection cable AG120.02.080
  • External power supply cable AG120.02.070
  • Grounding rod
  • Grounding cable
  • Battery alkaline R14 (12pcs.)
  • Contact magnetic
  • Set carrying bag
  • Receiver bag
  • Operation manual
  • Technical passport

Accessories

Sensor DKI-117 and Sensor DODK-117

Sensor DKI-117

Sensor DODK-117

Searching of cable faults at shorting of its armoring to the ground. Searching of outer insulation defects of metal pipelines (water, gas) at trenchless laying.

Pipe transmitter set MAG-05.X.XX

Pipe transmitter set MAG-05.X.XX

Sensor NR-117

Selection of the cable from a bunch.

Clamps CI-105

Clamps CI-105 Clamps CI-105/50 Clamps CI-105/110 Clamps CI-105/125
               Clamps CI-105                                      Clamps CI-105/50                          Clamps CI-105/110                           Clamps CI-105/125

Identification of the cable, the function “selection the cable from a bunch”. Non-contact connection to the pipelines or to the cable. Available in various sizes.

Power adapter AG 114M.02.020

Used for transmitter external power supply.

Download


Operation manual
3 MB


MapProgram